汽车换油保养DIY 

AFT,OIL FILTER..etc

概括步骤： 1.把车架高（如果你有条件的话，我换的时候因为没千斤顶，我是把轮子的一侧开到马路牙子上换的） 2：先把上面的机油盖拧开，然后爬到车下，在发动机的下面找个像容器一样的东西，上面有一个螺丝的那种（如图1） 。 3：找个盆之类的东西放在那个螺丝（也叫油堵或油嘴）下面，小心拧开螺丝当快完全掉下来的时候要迅速的把油堵拿下来如果太慢油会喷到你手上顺着手流到胳膊上，如果你刚熄灭车不久，要小心，油很烫，放完油就把油堵拧上去。（对了，要戴胶皮手套，很脏很脏不好洗） 4：等油漏差不多了，把机油滤芯拧下来，需要工具去拆要不使不上力，拆下来后再让油滴一会，滴完就把新的拧上去，拧上去就不用工具了，用手拧紧就好，（顺便说下机油滤芯90%都在车下面，有个别车是在发动机盖下面，比如BMW） 5：现在就把你的新机油加进去吧，4缸发动机加4L，6缸加6L，以此类推，尝试的加如果加到最后没把握那就加一点看下机油尺，别多也别少，在两条横线之间就行。[s:201] 结束了，就这么多，希望没落下什么步骤，哇哈哈。[s:200]  哦对了，新机油加完以后，要打着车让车着1分钟。磨合下

thanks for helping me write down the procedure....very detail [s:201]

when you see the debris from drained oil, that means your engine is getting hurt [s:212]

什么时候出个清积碳的DIY吧。。。

请教帅超哥，想给丰田换ATF WS，那个drain plug washer 要不要一起换？

[quote]引用第6楼山东于2011-01-14 08:28发表的  : 请教帅超哥，想给丰田换ATF WS，那个drain plug washer 要不要一起换？ [url=/club/job.php?action=topost&tid=264031&pid=6274069][img]/club/p_w_picpath/back.gif[/img][/url] [/quote] 要一起换......Thats what delar do every time,any oil change the washer has to be replaced to avoid leak from drain plug.The function for drain plug washer is to absorb the heat expansion between drain plug shank and oil pan. 如果不換, it may not leak right away,but when it start leaking,it will 1.mass up garage floor and environment. 2. cost you more money to drain out oil again and put that little new washer back lol.[s:208]

[quote]引用第5楼yw1015于2010-11-04 18:17发表的  : 什么时候出个清积碳的DIY吧。。。 [url=/club/job.php?action=topost&tid=264031&pid=6125981][img]/club/p_w_picpath/back.gif[/img][/url] [/quote] Injector clean, its just a flusing machine deliver chemical to your engine fuel injector line and let dirt or carbon burn off. I don't recommand to do this because 1. New car doesn't need it. 2. Old car doing this might cause engine leak if the chemical is too strong or too much pressure while doing the service. I recommand using Chveron highest Ocatne gas often when you drive on highway in highspeed, Chveron gas has techron that will clean carbon nuild up inside engine more efficent than the other brand of gas. Injector carbon flush cost you around 80 to 100 dollars more at Mr. Lube. If you spend few dollars more on high octane gas daily. No need 清积碳, I can show you picture next time when I am doing[s:201]

[quote]引用第7楼帥蛋超人于2011-01-15 06:55发表的 : 要一起换......Thats what delar do every time,any oil change the washer has to be replaced to avoid leak from drain plug.The function for drain plug washer is to absorb the heat expansion between drain plug shank and oil pan. ....... [url=/club/job.php?action=topost&tid=264031&pid=6283509][img]/club/p_w_picpath/back.gif[/img][/url] [/quote] 多谢了， 怎么我的贴下面这么多广告，干嘛呀

想知道这位哥哥是在哪换的机油啊？我也想去换了·· [s:201]

[quote]引用第10楼alberto-f于2011-01-15 10:06发表的 回 楼主(帥蛋超人) 的帖子 : 想知道这位哥哥是在哪换的机油啊？我也想去换了·· [s:201]    [url=/club/job.php?action=topost&tid=264031&pid=6284842][img]/club/p_w_picpath/back.gif[/img][/url] [/quote] 在車庫裡[s:201] 你要換油煞車在星期三和星期天電話我 6042185875 平時上班沒空..........[s:213]

[quote]引用第9楼山东于2011-01-15 07:58发表的  : 多谢了， 怎么我的贴下面这么多广告，干嘛呀 [url=/club/job.php?action=topost&tid=264031&pid=6283946][img]p_w_picpath/back.gif[/img][/url] [/quote] drain washer 材質厚度依各廠而異 請使用原廠的drain washer,雖然很貴 例如本田drain washer,2刀一個,簡直是打劫......[s:198] 但是至少用的放心

2：先把上面的机油盖拧开，然后爬到车下，在发动机的下面找个像容器一样的东西，上面有一个螺丝的那种 。 [s:206] [backcolor=#ff0000]初學者可能把変速箱油螺丝拧下来而不是机油[/backcolor][s:206] [s:212] [backcolor=#66ff00]AUDI,BMW,MB,and 高檔日系車底下包的跟粽子一樣,得先拆車底護板最少有6顆螺丝以上後才看的著发动机...（如图Audi A4 bottom view）..[[/backcolor]s:179] 3：找个盆之类的东西放在那个螺丝（也叫油堵或油嘴）下面，小心拧开螺丝当快完全掉下来的时候要迅速的把油堵拿下来如果太慢油会喷到你手上顺着手流到胳膊上，如果你刚熄灭车不久，要小心，油很烫，放完油就把油堵拧上去。 对了，要戴胶皮手套，很脏很脏不好洗）[backcolor=#ff3300]除了不好洗還會致癌[/backcolor][s:182] [backcolor=#ff0000]如果你刚熄灭车不久，要小心，油很烫,車底下发动机排氣管更烫, 先備好冰塊以防不測 [/backcolor] [s:221]

[quote]引用第12楼帥蛋超人于2011-01-15 14:56发表的 : drain washer 材質厚度依各廠而異 請使用原廠的drain washer,雖然很貴 例如本田drain washer,2刀一個,簡直是打劫......[s:198] ....... [url=/club/job.php?action=topost&tid=264031&pid=6287095][img]/club/p_w_picpath/back.gif[/img][/url] [/quote] 你这是机油的吧，我是想问ＡＴＦ的

Ya..I use engine oil drain plug washers for example. You can apply my theory on ATF washers ha[s:210]

3Q for coming to do oil change and brake fluid flush today Lawrence. Your Compass is now officialy pimped lol. [s:201]

有工具和技术，自己弄可以。少一项就don't brother 了。换下来的机油处理还是个问题。在国内都是直接下水道，没人管。

[quote]引用第17楼哥于2011-01-22 15:39发表的 : 有工具和技术，自己弄可以。少一项就don't brother 了。换下来的机油处理还是个问题。在国内都是直接下水道，没人管。 [url=/club/job.php?action=topost&tid=264031&pid=6326303][img]/club/p_w_picpath/back.gif[/img][/url] [/quote] Yes,any oil change or coolant waste, please bring to Canadian Tire,its free to dump infront of their garage shop haha Don't dump into the sewage because it will go into river and contaminate ecosystem. Canadian Tire 專回收机油 [s:196]

If your car is Mazda 5, it takes a while to remove the bottom cover with 7 screws. Therefore,if you want speed up,you can buy a cordless driver. This tool will definately speed up your job. And you or your friend won't lost his temper lol. Thanks for visiting again, Mr. Luo  [s:201]

Most Japanese cars have a jack point in the center of engine bottom. But make sure you find the right point not oil pan. Always follow with owner's manual to jack up the car with a pair of jack stands for safety. Safety first because if that car drop on you, you don't get second chance. The red mark that i draw is for Lexsus IS250 AWD. Any Lexsus owners can take a look if he wants to DIY.